WAXING
Melt ALL wax and pellets in the bag at once !
If you have the red dye? You will be melting wax, red dye, pellets, and powder. ALL AT ONCE.
Steps to wax the ramp:
1.
clean the surface of all other wax and dirt scraping or washing with soap water with a stiff brush.
clean the surface of all other wax and dirt scraping or washing with soap water with a stiff brush.2.melt all jump wax material in a metal buck big enough for the 9” paint roller
melt all jump wax material in a metal buck big enough for the 9” paint roller 3.get your wax to 270 degrees cold weather 320
get your wax to 270 degrees cold weather 320 4.take your wax to the ramp covered this saves the heat and prevents spilling
take your wax to the ramp covered this saves the heat and prevents spilling5.put the ramp at 5 ½’ ( gravity will help you wax the ramp )
put the ramp at 5 ½’ ( gravity will help you wax the ramp )6.have the low end and your 22’4” mark out of the water either float the low end or have some extra guys stand on the high end of the ramp
have the low end and your 22’4” mark out of the water either float the low end or have some extra guys stand on the high end of the ramp7.dip your roller in the wax covering the enter roller with wax
dip your roller in the wax covering the enter roller with wax8.Start on the RIGHT HIGH end of the ramp and roll gently down following the extra wax running down (gravity) as you go apply more pressure until you reach the end of the ramp. ** If your waxing the ramp in the lake DO NOT get your roller wet. If you do, get another roller **
Start on the RIGHT HIGH end of the ramp and roll gently down following the extra wax running down (gravity) as you go apply more pressure until you reach the end of the ramp. ** If your waxing the ramp in the lake DO NOT get your roller wet. If you do, get another roller **9.roll down never back up your same path this is very important to keep a smooth surface
roll down never back up your same path this is very important to keep a smooth surface10.once your at the bottom pick up your roller and start over again dip your roller and start a new line
once your at the bottom pick up your roller and start over again dip your roller and start a new line11.after you done you can scrap the lumps off the ramp although its not necessary
after you done you can scrap the lumps off the ramp although its not necessary Items to have:
1.metal bucket at least 9” wide for paint roller to fit in
metal bucket at least 9” wide for paint roller to fit in2.burner for melting wax
burner for melting wax3.temperature gage
temperature gage4.4 paint rollers *extras for mistakes*
4 paint rollers *extras for mistakes*5.a poll to screw in the end of the paint roller
a poll to screw in the end of the paint roller6.metal scraper
metal scraper 7.stiff brush for cleaning
stiff brush for cleaning RED WAX
This red wax is for ramps that are to bright or not a good color red.
If you are using the red dye follow these directions:
Put the little dye block and the UV powder in the wax while melting.
Follow all the directions the same.
Top to bottom in one stroke !!
Melt in a metal pan
Finish to the end of the ramp and make sure you wax pass the 22'4" mark !!!!!!!!
22' 4"
If your ramp doesn't look like this
your not going FAR !!
USA
Canada
Shipping included
sent US Mail Priority
photos by Lynn Novakofski
next day delivery
USA only
$55.00
USA
RED WAX
$100.00
RED wax
$85.00
$110.00
RED wax
$95.00
Europe
Asia
Australia
$95.00
RED wax
$105.00
waxing directions are at the bottom of the page
$65.00
clear wax
clear wax
clear wax
clear wax
PAYPAL will be performing maintenance for the next week
if paypal does not work you can send a check to
skifly
4105 ione ct
auburndale, fl 33823
